HOME

-

 I am Peijie.From last semester ,I have learnt the fusion 360 skill from the Introduction To Chemical Product module.I will update my leant new skill here also same likes last semster,So there are two personal goals in this semster for me:

a)master all the skill that have taught in eaxh lesson and put the effort as much as I can.

b)communicate with teamates well so can avoid the situations like last semester which cannot work together .


Since my old teamates,who are Clarence and Jiayu not same class with me in this semester, so I am grouped with Haijie and Yongjie.There what's we discuss about the team ground rules.

a)All teamates should contribute ,so we can easily settle some homework by combining the teamwork and it can prevent the situation like last semester just one person to work.

b)If someone cannot contribute should mention first so others can help and it doesn't matter to other if he mention before .

c)we should build up a team with high teamwork spirit and it is not in this module.We perhaps we can be friends in reality  and we can help each other throughout the life.

Comments

Post a Comment

Popular posts from this blog

Aurdino Programming

-
Image
I programme the arduino board by using Arduino IDE app which installed in the laptop.After I connect the USB Micro Port B with arduino board and mt laptop,then I open the Arduino IDE app and go to    File > Examples > Servo > Sweep. Then I adjust the value for pos value in the void loop part, one is used to  control the servo from  0 o  to 180 o  and the other is used to control the servo from   180 o  to 0 o    .Besides I also adjust the value for delay part  .As I finish adjusting these value so I can get the speed of servo motor moving desired. The code below is the source codes I used  #include <Servo.h> Servo myservo;  // create servo object to control a servo // twelve servo objects can be created on most boards int pos = 0;    // variable to store the servo position   void setup() {   myservo.attach(9);  // attaches the servo on pin 9 to the servo object } void ...
Read more »

HYPOTHESIS TESTING

-
Image
1.DOE PRACTICAL TEAM MEMBER 1. Person A (Jun Weng) 2. Person B (Roy) 3. Person C (Adam) 4. Person D (yongjie) 5. Person E (peijie) 2.FULL FACTORIAL DATA TABLE 3.FRACTIONAL FACTORIAL DATA TABLE SCOPE OF THE TEST The human factor is assumed to be negligible. Therefore different user will not have any effect on the flying distance of projectile. Flying distance for catapult A and catapult B is collected using the factors below: Arm length =  __ 28 __cm Start angle = ___ 20 __ degree Stop angle = ___ 60 __ degree Step 1: State the statistical Hypotheses: State the null hypothesis (H 0 ): The catapult that has 20cm arm length and start with angle 20 degree  and stop with 60 degree, the flying distance for both catapult A and B have no difference.   State the alternative hypothesis (H 1 ): The catapult that has 20cm arm length and start with angle 20 degree  and stop with 60 degree, the flying distance for both catapult A and B are different. Step 2: Formulate an analysis ...
Read more »

DESIGN OF EXPERIMENT

-
Image
FULL  FACTORIAL DESIGN Stop angle has the largest impact on the distance traveled by the projectile while arm length and start angle are relatively similar in terms of significance. FRACTIONAL  FACTORIAL DESIGN The results are similar to the full factorial design as the most significant factor is the stop angle followed by arm length and start angle. CONCLUSION I would recommend the full factorial. As by having only 16 data points, we already have cut down the number of runs to 2 each. So the data is already not as reliable. If we did fractional factorial, it might not give enough data for us to get accurate analysis and the right interactions. Furthermore, doing a full factorial for 16 data points is not considerably difficult, hence there should be no issues with doing the full factorial.  
Read more »