CAD

-

 Firstly,I create a rectangle with 65mm length and 25mm width




After I add the 2mm offset and fillet the 4 corners of rectangle and sketch dimension to it,I draw a circle with 5mm radius.



THEN,I text my name inside the rectangle.


After a few of process,the keychain have been done.




In conclusion,the designation of keychain is a basic skill in fusion 360.When I design the keychain ,it was refresh my knowledge about how to use the basic skill of fusion 360 which we have learnt in last semester.I hope that I can be faster to master all the skill of fusion 360 so I can design the model that we will use in the following practical  in this semester.

                                https://a360.co/3bpIikQ

WEEK 2 HANDPHONE DESIGN

Firstly,I create two triangle and make dimesion to them about 4 mm for width and 120mm for length.Then adjust the angle about 72 degree for that like shown below.

Then finish sketch and I try to extrude them which the bigger to 70 mm but for smaller one to 35 mm.


After that I extrude the smaller one to 70mm.

Then I combine them and choose the cut operation and tick for keep tool option.

Finally I fillet all the corner with 3mm.

Then it is done.


https://a360.co/3C7A8sa


Comments

Post a Comment

Popular posts from this blog

Aurdino Programming

-
Image
I programme the arduino board by using Arduino IDE app which installed in the laptop.After I connect the USB Micro Port B with arduino board and mt laptop,then I open the Arduino IDE app and go to    File > Examples > Servo > Sweep. Then I adjust the value for pos value in the void loop part, one is used to  control the servo from  0 o  to 180 o  and the other is used to control the servo from   180 o  to 0 o    .Besides I also adjust the value for delay part  .As I finish adjusting these value so I can get the speed of servo motor moving desired. The code below is the source codes I used  #include <Servo.h> Servo myservo;  // create servo object to control a servo // twelve servo objects can be created on most boards int pos = 0;    // variable to store the servo position   void setup() {   myservo.attach(9);  // attaches the servo on pin 9 to the servo object } void ...
Read more »

HYPOTHESIS TESTING

-
Image
1.DOE PRACTICAL TEAM MEMBER 1. Person A (Jun Weng) 2. Person B (Roy) 3. Person C (Adam) 4. Person D (yongjie) 5. Person E (peijie) 2.FULL FACTORIAL DATA TABLE 3.FRACTIONAL FACTORIAL DATA TABLE SCOPE OF THE TEST The human factor is assumed to be negligible. Therefore different user will not have any effect on the flying distance of projectile. Flying distance for catapult A and catapult B is collected using the factors below: Arm length =  __ 28 __cm Start angle = ___ 20 __ degree Stop angle = ___ 60 __ degree Step 1: State the statistical Hypotheses: State the null hypothesis (H 0 ): The catapult that has 20cm arm length and start with angle 20 degree  and stop with 60 degree, the flying distance for both catapult A and B have no difference.   State the alternative hypothesis (H 1 ): The catapult that has 20cm arm length and start with angle 20 degree  and stop with 60 degree, the flying distance for both catapult A and B are different. Step 2: Formulate an analysis ...
Read more »

DESIGN OF EXPERIMENT

-
Image
FULL  FACTORIAL DESIGN Stop angle has the largest impact on the distance traveled by the projectile while arm length and start angle are relatively similar in terms of significance. FRACTIONAL  FACTORIAL DESIGN The results are similar to the full factorial design as the most significant factor is the stop angle followed by arm length and start angle. CONCLUSION I would recommend the full factorial. As by having only 16 data points, we already have cut down the number of runs to 2 each. So the data is already not as reliable. If we did fractional factorial, it might not give enough data for us to get accurate analysis and the right interactions. Furthermore, doing a full factorial for 16 data points is not considerably difficult, hence there should be no issues with doing the full factorial.  
Read more »